Free cabinet design, material planning, nesting, and 3D. Plan frameless or face-frame cabinets in the browser, with optional SketchUp export.
Project JSON: checking...
Browser recovery is automatic. Save project writes the connected JSON file; Save As chooses a different file.
Shop mode
A focused workbench for cutting and assembly. Filter the current project, check off parts as you make them, and keep the full design intact.
Cabinets
Label
Type
Front construction
Box / carcass material
Faces / fronts material
Hinge side single door
Width
Qty
Vertical stack / clear openings bottom → top
Custom drawer-front heights optional; drawers only
Shelves count fallback
Drawer / mixed stack syntax:O means the LETTER O ("oh") for Open — not the digit zero (0). For example, D7, O9.5, D7 means drawer, open cubby, drawer. Adjacent open entries stay separate: D4.75, O12, O12, D4.75 makes two 12" clear cubbies with a fixed divider between them. You may write Open 9.5 instead of O9.5 if that is clearer. An all-number list such as 7, 7, 9.5 remains legacy all-drawer mode. Once you use D to mark drawers, any bare number is also interpreted as an open cubby: D9, D9, 15 means two 9-unit drawers with a 15-unit clear cubby above. Materials: cabinet rows can use the project defaults or override the plywood species for that cabinet's box/carcass and faces/fronts. Open-shelf cabinets: use the same field for clear opening heights, bottom to top, for example 9.5, 12, auto. Each boundary between openings gets an adjustable pin-supported shelf; auto is allowed only for the final/top opening and uses the remaining clear height. If the field is blank, the Shelves count still creates evenly spaced adjustable shelves. Values use the selected unit; explicit mm or in suffixes are also accepted.
Per-cabinet carcass material: use each row's Box / carcass material selector to choose Birch plywood or Cherry plywood for that cabinet. The Default (...) choice keeps the current type-based default and updates when the project material defaults change. The selected carcass material is used in the BOM, cut list, 3D preview, and SketchUp export.
3D Preview
Built into CabinetDrafter — no SketchUp or internet connection required.
Drag to orbit · mouse wheel to zoom · Shift-drag to pan · double-click to fit.
BirchCherryBlack outlines show individual pieces.
Optional SketchUp export
Show cabinet labels in 3D / SketchUp
Turn this off for a clean presentation model with no cabinet summary text labels.
Show cabinet width labels in 3D / SketchUp
Shows each cabinet's overall width as a short label centered near the front bottom of the cabinet.
Show drawer box height labels in 3D / SketchUp
Shows the entered drawer-box wall height for each drawer, formatted as a woodworking fraction in inch mode or millimeters in mm mode.
Show drawer face height labels in 3D / SketchUp
Shows the visible drawer-front height for each drawer. Labels are placed directly at the center of each face; when both options are on the number order is box / face.
Show open-space height labels in 3D / SketchUp
Shows the clear vertical height centered in each mixed-cabinet cubby and each opening in an open-shelf cabinet, formatted as a woodworking fraction in inch mode or millimeters in mm mode.
Replace prior Generated Cabinet Lineup in SketchUp
Turn this off to keep existing generated cabinets and add the new export as a separate timestamped group.
Units
The project is stored internally in inches for SketchUp compatibility. Switching units converts the displayed values without changing cabinet geometry.
Use in SketchUp Pro
Open Extensions → Developer → Ruby Console and run:
Each Ruby download gets a unique timestamped filename so SketchUp cannot accidentally reload an older copy. After downloading, the page shows the exact load command. By default the script replaces the prior Generated Cabinet Lineup; turn off that export option to keep existing generated cabinets and add the new run as a separate timestamped group. The script models drawer boxes, mixed open cubbies/divider panels, toe-kick bases and skins, fronts/doors, optional cabinet summary and width labels, independently selectable per-drawer box-height and face-height labels, and saves a native SKP to your Desktop.
Drawer sizing
24" for your 24" slides.
Default 1" total = 1/2" each side.
Default 1/2". Material is selected below.
Default 1/2"; panel fits completely between the four drawer walls. Material is selected below.
The default is the existing geometry. Rabbet, box-joint, and dovetail choices use full-width front/back blanks and require the selected corner machining.
Floating and captured bottoms extend into 1/4" wall grooves. The panel remains removable only if the front or back is designed for access.
Used by the 1/4" rabbet option; set to your actual router/saw setup.
Machining note only; it does not reduce the blank size.
Default 1/4". Groove depth cannot exceed the wall thickness in the modeled fit.
Default 1/2". This is a design choice, not a slide standard.
Default 1/2" above the cabinet bottom. Drawer boxes are stacked upward from here.
Default 24". Horizontal panels that form the top/bottom of an open cubby.
Width rule: drawer box outside width = cabinet inside width − total slide clearance. Height rule: drawer boxes must fit between the top of the 3/4" cabinet bottom and the underside of the 3/4" top stretchers, so the default 38" carcass has 36.5" of internal vertical drawer-box space. Vertical drawer spacing is not standardized by the slides. Drawer boxes and open cubbies are stacked from the bottom upward. The drawer-box gap applies between adjacent drawer boxes; fixed 3/4" divider panels separate drawers from open cubbies and separate adjacent open cubbies. Open-cubby heights are clear opening heights. A top open cubby is anchored to the underside of the top stretchers so its entered clear height is exact. Verify your slide manufacturer's horizontal clearance before cutting. Joinery note: the app reports rectangular stock blanks and assumes you make the selected rabbets, fingers, dovetails, or grooves during machining. Confirm your actual cutter and fit before cutting a project.
Default pure drawer cabinet boxes and toe-kick structural rails.
Drawer sides, fronts, backs, and bottoms.
Horizontal panels that form the top/bottom of open cubbies.
Open-shelf backs and localized mixed-cubby backs. Single-door backs match the face/front material.
Cabinet-row material selectors override these defaults per cabinet. Default box/carcass material means pure drawer cabinets use the hidden cabinet-box plywood, while mixed, open-shelf, and single-door cabinet boxes use the face/front plywood because those parts are visible.
Face-frame options
Default 1 1/2". Full-height left/right members.
Default 1 1/2". Top and bottom perimeter rails.
Default 3/4". Frame is applied to the front of the carcass.
Face-frame members are treated as linear solid-wood stock, not plywood-sheet parts.
Default 1/2" per edge for face-frame overlay fronts.
Default 1/16" around inset doors/fronts.
Face frames are currently perimeter frames: two full-height stiles plus a top and bottom rail. CabinetDrafter does not yet generate intermediate face-frame rails between individual drawers or cubbies. Overlay and inset front sizing is calculated against the perimeter frame opening.
Drawer / mixed sizing preview
Standard cabinet dimensions
Default 1/4". Applied to open spaces and single-door cabinets on the outside rear face.
Default 1/8" top, bottom, and between drawer fronts.
Default 1/16"; two abutting cabinets then have a 1/8" seam.
Default 1/4". Uses the visible/front material unless you substitute veneer manually.
Front pulls
Pull 1
Pull 2
Two reusable pull choices. Override a cabinet or individual drawer under Front pulls in its row. Drawers use a horizontal pull centered across the face near the top; doors use a vertical pull centered on the edge opposite the hinges. Hardware is shown schematically; dimensions are visual planning sizes, not drilling patterns or mounting-hole spacing. Sizes and edge distances are limited to fit each face. Cut-out dimensions and templates are configured below; hardware replaces the cut-out on its face. Hardware is excluded from plywood nesting and the BOM.
Front pull cut-outs
Drawer tops and door pull edges
Cut-outs are secondary operations on the rectangular front blanks.
Circular segments make crescent or half-circle pull openings.
Drawer notch width; door notch height.
How far the notch enters the front.
Set near half the width for a half-circle style.
The full diameter used to form the circular arc.
Segment depth from the face edge. Must be no greater than the diameter.
The opening width, calculated from diameter and segment depth.
Drawer notches open from the top edge. Single-door notches are centered vertically on the edge opposite the configured hinge side. Circular chord/segment mode uses the entered diameter and depth to calculate the chord width automatically. Dimensions are limited when a cut-out cannot fit the front.
Printable pull cut-out templates
3D router-bushing template
Diameter of the bit that will cut the face.
The bushing diameter that rides on the printed opening.
Available vertical guide height. The printed jig should be thinner than this.
Separate from bushing thickness; default is 1/8".
The STL opening is enlarged by half the diameter difference so the bit cuts the configured pull shape. The jig has wide clamp wings, top locating tabs, and a raised center reference. STL units are inches; import at 100% scale.
Plywood sheet planning
Default 48".
Default 96".
Default 1/8".
Default 1/4" trim around each sheet.
Added to the nested layout count.
Applies to all Birch plywood thicknesses.
Applies to all Cherry plywood thicknesses.
Side-by-side faces places tall doors/fronts next to one another along their long edges.
Preserve visible grain direction
Recommended for fronts, doors, visible shelves, sides, backs, and toe-kick skin.
Faces-only scope lets hidden shelves, carcass sides, and other non-face parts rotate for better Cherry yield.
Put cabinet faces on dedicated sheets
Door and drawer-front parts share sheets only with other faces of the same material, never with carcass or drawer-box parts.
Keep each cabinet's faces together
Each cabinet instance gets its own face-sheet group, while non-face parts may fill unused space. If all faces cannot fit on one sheet, the layout identifies the overflow.
Cutting-layout assumption: sheet grain runs along the 96" direction. Grain-sensitive parts are oriented so the face grain runs the expected direction when preservation is on. The all-parts scope preserves the existing behavior; faces-only scope lets hidden cabinet and drawer-box parts rotate for better yield. Dedicated face sheets can increase the total sheet count because faces cannot use leftover space beside other parts.
Build progress & sheet inventory
Progress tracks physical plywood cut parts. Check off whole carcasses or drawers for speed, or open the physical-parts table for piece-by-piece control. Checked work stays in the project design and 3D model, but it is removed from the remaining-work nesting below. Full sheets on hand means uncut, full usable sheets only; scraps and partial sheets are not counted as full-sheet inventory.
Shopping list of sheets still to buy
Completed cut parts
Material / sheet BOM full project
Plywood cutting layouts
By default these layouts show remaining cut parts only. Turn on Keep cut pieces on diagrams to show the full project layout with checked cut pieces still in place. Click a part or its small checkbox to mark it cut or return it to the remaining work list. Parts are grouped into horizontal strips: dashed guides mark full-width cuts across the sheet, followed by cuts within each strip. Parts use black-and-white hatch fills by species; the sheet material and thickness are named in the sheet header. Each part has a short pencil mark such as 2 A: the cabinet number followed by a letter for that physical piece. The detailed cabinet, part name, and dimensions remain printed below it. Real sheets may have voids, damage or grain defects, and your final saw strategy may move pieces around. The optimizer includes the selected kerf and edge trim.
Construction rules in this version
Cabinets may be frameless, face-frame overlay, or face-frame inset on a per-cabinet basis. Structural carcass joints use pocket screws in the supplied project defaults. Pure drawer cabinets use the hidden cabinet-box material and remain open-backed unless the cabinet row overrides the box/carcass species. Single-door cabinet boxes, shelves, and mixed/open visible cabinet parts default to the face/front material, and each cabinet row can override box/carcass and face/front species independently. Single-door applied backs match the door/front material. Face frames are modeled as solid-wood perimeter frames and are reported separately as linear stock. Drawer boxes use the drawer-box material with bottoms fitted completely between the four walls. Open spaces receive applied backs at the rear. Adjustable shelves are pin-supported; fixed mixed-cubby dividers are pocket-screwed. Countertops attach through top stretchers. No edge banding is included.
Toe-kick/base: each cabinet gets a separate 2"-high ladder frame using the hidden cabinet-box material, intended to use offcuts. A separate visible skin uses the cabinet's face/front material. The BOM treats adjacent cabinets with the same face/front species as one installed run and makes the skin in the longest pieces that fit the configured sheet length; SketchUp shows one skin segment per cabinet because the presentation model spaces cabinets apart.